Photonics Map

How to choose a tunable laser: diode, solid-state, dye or OPO

Tunable sources differ more than any other laser family, from a few gigahertz of fine tuning to hundreds of nanometers. The choice follows from how far you must tune, how narrow the line must be, and where in the spectrum you work. Not a ranking of suppliers.

Supplier directory · By Photonics Map · reviewed 2026-11

Ti:sapphire range
roughly 650–1100 nm
Diode, grating or DBR
40 nm and more
Diode, temperature only
a few nm

Who this guide is for

Engineers and lab managers specifying a wavelength-tunable source for spectroscopy, device characterization, atomic physics, telecom test or sensing who need to decide between a tunable diode laser, a tunable solid-state laser, a dye laser, a tunable fiber laser or an optical parametric oscillator.

What tunable means in practice

A tunable laser is one whose emission wavelength can be adjusted during operation, not just set at the factory. RP Photonics stresses that the characteristics differ greatly. Single-frequency lasers have a very narrow line, and tuning them over a large range without mode hops needs relatively sophisticated technology. Lasers that run on many resonator modes at once only shift the envelope of the spectrum when tuned. Optical parametric oscillators are not lasers but are often counted among tunable sources.

Decision table: which tunable source for which job

Pulse regimes compared for buyer decisions
SourceBest atStrengthChoose when
External-cavity diode laser40 nm and moreGrating in the cavity gives wide tuning with a small linewidth.Continuous-wave spectroscopy, laser cooling, device test within one diode's band.
DFB or DBR diode lasera few nm, fineTuned by temperature or current. DFB is the more reliable single-frequency design.A narrow single frequency near a fixed wavelength, such as an absorption line.
Ti:sapphire, Cr:ZnSe, Cr:ZnShundreds of nmTi:sapphire spans roughly 650–1100 nm. Cr:ZnSe and ZnS reach the mid-infrared. Hundreds of mW to watts.Wide tuning with power and beam quality. High cost, largely from the pump.
Dye laservisible, wideDifferent dyes cover the ultraviolet to near infrared. Dye degrades and is hazardous.Visible wavelengths other sources miss, mostly spectroscopy.
Rare-earth fiber lasertens of nmErbium types often tune tens of nm, sometimes over 100 nm, across one or two telecom bands.Tuning within the C or L band with fiber delivery.
Optical parametric oscillatorwidest, mid-IRPhase matching sets the wavelength, so tuning can be extremely wide. Needs a laser pump.Wavelengths no laser reaches, mainly mid-infrared. Expect a pumped system.

How to choose

  1. 01

    Write the tuning requirement as three numbers

    How far you must tune (a few GHz, a few nm, tens or hundreds of nm), how narrow the line must be, and whether you need mode-hop-free tuning across the whole range. RP Photonics says tuning over a large range without mode hops needs relatively sophisticated technology, so a datasheet range is not the same as a continuous, mode-hop-free range.

  2. 02

    Separate coarse tuning from fine tuning

    Coarse tuning changes the wavelength band, by a grating, a birefringent tuner, an etalon or the phase-matching condition in an OPO. Fine tuning changes the frequency by cavity length or diode current or temperature, within the free spectral range. RP notes that a non-planar ring oscillator tunes continuously within a few gigahertz by piezo stress or crystal temperature. Ask which mechanism covers which part of your range.

  3. 03

    Check what the source needs to run

    Ti:sapphire and OPO systems need a pump laser. RP says the cost of Ti:sapphire comes largely from the pumping requirements, typically several watts and sometimes 20 W, and that an OPO requires a high-intensity, spatially coherent pump, in most cases a DPSS laser. Dye lasers add dye handling and toxicity. Include the pump and the consumables in the comparison.

  4. 04

    Decide between narrow line, high power and wide range

    These trade against each other across families. Diodes give narrow lines at modest tuning range. Ti:sapphire gives wide range and watts. OPOs give the widest range and reach the mid-infrared. Supercontinuum sources cover a very wide range but are much more limited in radiance and spectral radiance (RP Photonics), so they suit broadband needs rather than narrow-line ones.

How to shortlist suppliers

  1. 01

    Write the wavelength sheet

    Target wavelength or range, line width, tuning range, continuous or swept tuning, mode-hop-free range, power at the target, continuous or pulsed, and delivery by fiber or free space.

  2. 02

    Ask each supplier the same questions

    Mode-hop-free range and what limits it, tuning speed and mechanism, power across the tuning range and not only at the peak, what pump or consumables are required, and what the supplier measured. A supplier's figure describes that supplier's laser only.

  3. 03

    Then browse suppliers

    Use the tunable laser category to find companies, and the diode and fiber laser categories for sources not listed under tunable. Listing order is not a ranking of quality or suitability.

Ready to browse companies? Open the supplier hub.

Frequently asked questions

›What is the widest tunable source?

Optical parametric oscillators offer extremely wide tuning ranges spanning the visible, near and mid-infrared, and reach wavelengths that lasers cannot (RP Photonics). Among true lasers, Ti:sapphire, Cr:ZnSe and Cr:ZnS tune over hundreds of nanometers, and dye lasers cover very broad ranges with different dyes.

›How far can a tunable diode laser tune?

Most laser diodes tune over a few nanometers by changing the junction temperature. External-cavity diode lasers and distributed Bragg reflector lasers can tune over 40 nm and more with additional means such as an intracavity grating (RP Photonics).

›What is mode-hop-free tuning?

Tuning in which the optical frequency changes smoothly, without discontinuous jumps between resonator modes. RP Photonics says achieving it over a large range requires relatively sophisticated technology, so check the mode-hop-free range separately from the headline tuning range.

›Is an OPO a laser?

No. An OPO uses parametric amplification in a nonlinear crystal instead of stimulated emission, though it uses a resonator and has a pump threshold like a laser (RP Photonics). It is often included with tunable laser sources.

›Why are Ti:sapphire lasers expensive?

RP Photonics attributes the relatively high cost largely to the pumping requirements: several watts of pump, sometimes 20 W, at blue-green wavelengths where powerful diodes are less readily available. For that reason Ti:sapphire is used mostly where its tuning range or ultrashort pulses are essential.

Sources

Figures are the commercially common cases, not physics records. Where sources disagree the page gives a range and says so.

How to Choose a Tunable Laser: Diode, Dye, Ti:Sapphire, OPO · Photonics Map