Fiber vs CO₂ laser: which source for your material
A decision guide for cutting, welding and marking. The choice is driven first by what your material absorbs, then by thickness, beam delivery and operating cost. Not a supplier ranking.
Supplier directory · By Photonics Map · reviewed 2026-11
- CO₂ wavelength
- typically 10.6 μm (lines 9–11 μm)
- Fiber laser wavelength
- around 1 μm (Yb-doped)
- CO₂ wall-plug efficiency
- about 10–20 %
- Fiber cable for high-power CO₂
- none available
Who this guide is for
Process engineers and buyers specifying a laser for cutting, welding or marking who must pick between a fiber laser (around 1 μm) and a CO₂ laser (10.6 μm). For sub-picosecond sources, use the ultrashort-pulse guides instead.
The two sources in plain terms
A fiber laser uses an optical fiber doped with rare-earth ions (for example ytterbium) as its gain medium; many materials-processing machines use continuous-wave versions, and the 1 μm region is the wavelength range RP Photonics groups fiber and YAG lasers under. A CO₂ laser is a molecular gas laser, electrically pumped, that typically emits at 10.6 μm, with dozens of other lines between about 9 and 11 μm. The two wavelengths differ by about a factor of ten, and that difference decides most of the comparison: how strongly each material absorbs the beam, whether the beam can travel in a fiber cable, and what optics the machine needs.
Decision table: fiber vs CO₂
| Material or need | Which source leads | Strength | Choose when |
|---|---|---|---|
| Metals | fiber absorbed better | The 1 μm wavelength is absorbed more efficiently by metallic workpieces than 10.6 μm (RP Photonics). CO₂ lasers do cut and weld stainless steel, aluminum and copper, at multi-kilowatt power. | Metal sheet and plate is most of your work: start with fiber. Keep CO₂ on the list only if you already run one or need mixed-material capability. |
| Plastics, wood, acrylic, die boards | CO₂ absorbed strongly | Materials such as wood and acrylic absorb strongly around 10.6 μm; RP Photonics lists cutting and structuring plastics, wood and die boards as the main CO₂ uses, mostly at 20–200 W. | Non-metals dominate: CO₂ is the default. A fiber laser at 1 μm is not an equivalent substitute for these materials. |
| Glass and ceramics | CO₂ absorbs at the surface | Most glasses absorb strongly near the surface at 10.6 μm, and local heating can drive a crack (RP Photonics, laser cutting). RP also describes CO₂ beams as favorable for polymers and ceramics. | Thermal glass separation or ceramic work: CO₂ is a candidate. Inside-glass modification needs an ultrashort-pulse source, not either of these. |
| Beam delivery | fiber cable vs mirrors | RP Photonics states there are no high-power fiber cables for CO₂ radiation, because no material is transparent enough near 10 μm. 1 μm beams can be delivered by fiber cable. | Robot-mounted heads, multiple workstations from one source or remote cutting: fiber. Fixed flatbed: delivery does not decide it, so use material. |
| Efficiency and cooling | fiber usually higher | RP Photonics gives CO₂ wall-plug efficiency as roughly 10–20 % and says fiber lasers often have a significantly higher one than bulk lasers. It gives no single fiber figure, so compare quoted wall-plug numbers from suppliers. | Running hours are high and electricity is a large share of cost: ask each supplier for measured power draw at your cutting power, per RP Photonics' point that electricity and gas use drive operating cost. |
| Thick sections | both used; check your supplier | RP Photonics says multi-kilowatt continuous-wave fiber lasers cut metal from thin sheet to plate several tens of millimeters thick, depending on material, power, gas and edge quality. It also notes CO₂ lasers remain widely used for parts thicker than a few millimeters. | Plate work: require cut samples in your material and thickness from each supplier. A limit quoted for one machine is not a limit for the category. |
| Optics and safety | CO₂ needs IR optics | CO₂ systems use infrared optics, often zinc selenide (ZnSe) or zinc sulfide (ZnS). At low intensity the long wavelength is relatively eye-safe, but high power and high drive voltages still raise serious safety issues (RP Photonics). | RP Photonics notes a cutting machine needs an interlocked enclosure or a restricted controlled area, plus fume extraction. |
How to choose
- 01
Start from the material list
List every material and thickness you will cut over the next two or three years, with the share of work each represents. If metals dominate, fiber is the natural starting point because of absorption and fiber delivery. If wood, acrylic, plastics or die boards dominate, CO₂ is. Mixed shops can need both, or can accept slower processing of the minority material.
- 02
Decide how the beam gets to the part
If the head must move on a robot arm or the source must serve several stations, the absence of a high-power fiber cable for 10.6 μm is a hard constraint.
- 03
Compare operating cost on measured numbers
Ask for electricity consumption and assist-gas consumption per meter of cut, plus maintenance intervals, at your material and thickness. RP Photonics names these as a substantial part of operating cost. Do not compare datasheet efficiency percentages alone.
- 04
Require sample cuts
Absorption tells you which source is favored, not whether a given machine meets your edge quality and speed. Ask each shortlisted supplier to cut your material and thickness and report kerf, edge condition and cutting speed.
How to shortlist suppliers
- 01
Write the process sheet
Materials, thicknesses, required edge quality, parts per shift, and whether the head moves on a robot. That sheet picks the wavelength before it picks a brand.
- 02
Ask for the same data from every supplier
Rated power at the workpiece, measured power draw, assist-gas use, sample cut results, optics and consumable lifetime, and service coverage in your region. A vendor figure describes that vendor's machine only.
- 03
Then browse suppliers
Use the fiber laser and CO₂ laser categories to find companies. Listing order is not a ranking of quality or suitability.
Ready to browse companies? Open the supplier hub.
Frequently asked questions
›Is a fiber laser better than a CO₂ laser?
Neither is better in general. Fiber lasers are favored for metals because 1 μm light is absorbed more efficiently and can travel in a fiber cable. CO₂ lasers are favored for wood, acrylic, plastics and similar materials that absorb strongly at 10.6 μm (RP Photonics).
›Can a CO₂ laser cut metal?
Yes. RP Photonics lists cutting, welding and cladding of stainless steel, aluminum and copper with multi-kilowatt CO₂ lasers, and notes CO₂ lasers remain widely used for cutting and welding parts thicker than a few millimeters.
›Why can't a CO₂ laser use a fiber cable?
RP Photonics states there are no optical fibers for high-power 10 μm beams, since there are no suitable materials with very high transparency in that region. CO₂ systems deliver the beam with mirrors and infrared optics.
›How efficient is each type?
RP Photonics gives roughly 10–20 % wall-plug efficiency for CO₂ lasers, and says fiber lasers often have significantly higher efficiency than bulk lasers. We have not found a single sourced fiber figure that applies to the whole category, so ask suppliers for measured power draw.
›What are the other CO₂ wavelengths for?
Most commercial CO₂ lasers emit at 10.6 μm, but some are optimized for other lines such as 9.3 or 10.25 μm, which certain materials, for example polymers, absorb much more strongly. Standard 10.6 μm optics may reflect too strongly at these wavelengths, so special optics can be needed (RP Photonics).
Sources
- RP Photonics Encyclopedia: CO2 lasers · 10.6 μm and 9–11 μm lines; 10–20 % efficiency; ZnSe/ZnS optics; no high-power fiber cables; applications; competition with 1 μm lasers
- RP Photonics Encyclopedia: Fiber lasers · doped-fiber gain medium; use in cutting and welding; continuous-wave machines
- RP Photonics Encyclopedia: Fiber lasers versus bulk lasers · fiber lasers often have significantly higher wall-plug efficiency than bulk lasers
- RP Photonics Encyclopedia: Laser cutting · lasers used for cutting; multi-kW fiber thickness range; glass absorption at 10.6 μm; operating cost drivers
Figures are the commercially common cases, not physics records. Where sources disagree the page gives a range and says so.